Continuous Emission Monitoring. James A. Jahnke
Читать онлайн книгу.
continued to serve as a resource for training programs, the development of quality assurance plans, and the drafting of technical specifications for monitoring system purchases. It is a characteristic of U.S. environmental programs, that once written, regulations do not go away. In some cases they may be revised, but in others, they remain static. Continuous emission monitoring requirements have accordingly remained relatively unchanged over the past four decades. U.S. CEM requirements have remained basically the same since their inception in the 1970s, seeing only their greatest alteration with the allowance trading programs implemented in the 1990s. In terms of technology, extractive sampling methods, in situ monitoring, the principles of light absorption and light scattering, and other analytical methods applied in the monitoring instrumentation are fundamental; providing the basis for understanding the operation of instruments that typically remain installed from 15 to 30 years. However, much has been learned over the past 20 years and an update of the second edition is needed to provide a current perspective of the field. In particular, the U.S. Environmental Protection Agency institutes new rules and requirements as required by the periodic amendment of the Clean Air Act. These new rules are added to extend control over a wider range of industries for a wider range of pollutants. This edition of Continuous Emission Monitoring addresses these rules and the technology applied to meet them.
This book examines the interplay of technology and regulation as it affects the design, application, and certification of CEM systems. It describes new techniques employed in emissions monitoring, adds new knowledge gained on existing methods, but excludes instrumentation that is no longer available commercially. Chapters on the measurement of air toxics, mercury, and greenhouse gases have been added. The chapter on air toxics discusses monitoring instrumentation and methods used to measure hazardous air pollutants regulated under 40 CFR 63, the so‐called MACT (Maximum Achievable Control Technology) program. Monitoring for mercury is also required under this rule; however, due to the complexity of both the monitoring technology, calibration methods, and certification requirements, a separate chapter is devoted to this topic. A chapter on greenhouse gas monitoring has also been added. Monitoring greenhouse gases is relatively straightforward; however, data quality is paramount in this area of measurement. The role of CEM systems in greenhouse gas reporting is discussed in relation to the use of mass balance, emission factors, and other estimates to provide perspectives in reporting and certifying greenhouse gas information.
Due to the expanded use of CEM systems in regulatory programs both in the United States, Canada, Europe, and Asia, it is important for data comparability between nations that both the monitoring technology and regulatory standards used for system specification be technically sound. Additional emphasis is given to international approaches to continuous monitoring, particularly approval methods for the “automatic monitoring systems” (AMS) of the European Union (EU). Differences between the U.S. and European methods are discussed with regard to data equivalence and the implications for international agreements.
CEM technology can be considered to be mature for the continuous measurement of gases such as SO2, NO, CO, O2, and CO2, in addition to the measurement of particulate matter, mercury, and flue gas volumetric flow. By mature, it is meant that sufficient knowledge has been attained over the past 50 years of CEM development so that when properly designed, operated, and maintained, these CEM systems can be used to measure emissions to within acceptable levels of precision and accuracy. Advances in the application of digital electronics have greatly improved monitoring instruments, as well as continuing the trend to smaller, more cost‐effective, and less maintenance intensive instruments. But CEM systems do remain application dependent. An instrument manufacturer's new analyzer or a CEM systems integrator's innovative design must still be evaluated with respect to plant‐specific requirements as well as the ever more demanding regulatory requirements. In terms of present realities, the first law of CEM systems that “there is no best type of system” may be rephrased more positively. The best system is one that (i) works in the plant application, (ii) can be purchased and operated at “reasonable cost,” and (iii) requires relatively low maintenance. It is, however, not always easy to obtain that one best system when confronted with marketing claims, conflicting performance histories, cost limitations, and installation deadlines.
This third edition is written in the same spirit as the first and second, presenting the principles by which CEM system technical and regulatory developments can be understood. This book is designed to be comprehensive in scope, to meet the needs of both the plant environmental engineer applying CEM systems and control agency personnel incorporating CEM systems in regulatory programs.
Although the chemical or physical basis of analyzer operation is given, the theoretical and technical details necessary for designing monitoring instrumentation and systems is beyond the scope of this book. Ample references are incorporated after each chapter should the reader wish to further pursue specific topics. This edition of Continuous Emission Monitoring, as the first and second editions, seeks to introduce the reader to this dynamic field and to point the way to the knowledge of today's CEM systems necessary to address the challenges of today's regulatory environment.
The author would like to thank the graphic artists who have contributed to the evolution of the figure illustrations presented in this book. These artists include Katherine Lindsay and Betsy Huber who initiated many of the original CEM system dimensional drawings, Sherry Stafford who prepared the graphics for the first edition, and John Havel who developed the new graphics for both the second edition and this third edition. The author is indebted to the instrument manufacturers and CEM system integrators who graciously furnished diagrams and technical information of their instruments and systems. Thanks are also expressed to Kata Kollath for assistance in editing, and the colleagues who offered suggestions for the development of this edition and pointed out errors in the second edition.
James A. Jahnke, PhD
CHAPTER 1 INTRODUCTION TO CEM SYSTEMS
In the early 1970s, a better way was needed to monitor stack emissions than by manual stack tests. In general, manual methods are conducted by inserting a probe into a stack, extracting a sample, and analyzing the sample in a laboratory, which is a time‐consuming process. Manual source tests also require a degree of preparation, and the coordination and prior scheduling of a test may result in source operations being highly tuned before such testing takes place. Manual test results, therefore, may not necessarily be representative of day‐to‐day emissions. Clearly, for monitoring plant emissions and the performance of pollution control equipment on a more realistic basis, alternative measurement techniques are needed.
A BRIEF HISTORY
Attempts were made in the 1960s to use ambient air analyzers and process industry analyzers to measure source emissions. Ambient air analyzers were not successful at that time due to the instability of dilution systems. However, process analyzers did prove to be useful, particularly those that employed ultraviolet and infrared photometric techniques. Then, in the late 1960s and early 1970s, successful developments emerged in instrumentation in Germany and the United States. Ambient analyzers were redesigned to measure gases at higher concentration levels, and the so‐called “in‐situ” analyzers were developed, which can measure gases in the stack without sample extraction. These methods, in addition to new German optical systems for opacity monitors and the development of luminescence measurement techniques in the United States, provided a technological base from which continuous emission monitoring (CEM) regulations could be established.
Continuous emission monitoring requirements in the United States were first promulgated in 1971. However, the CEM industry did not begin to develop until after 6 October 1975 when the U.S. Environmental Protection Agency (U.S. EPA) established performance specifications for CEM systems and required their installation in a limited number of sources. Since then, CEM systems have been applied to a wider range of sources, and over 50 years of experience has led to the evolution of analyzers and monitoring systems with ever‐improving performance The technology is considered mature, having a solid foundation in reliable instrumentation, procedures, and standards that can assure the quality of source emission data at specified limits of accuracy and precision.