Electrical Safety Engineering of Renewable Energy Systems. Rodolfo Araneo
Читать онлайн книгу.
1.2), it is conservatively assumed an adiabatic process. Such a process calls for no heat removal into neighboring tissues by blood flow or by conduction and/or convection into the air, but it is presumed that all the heat stays within the tissue.
Vues of ionic conductivity of some biological tissues are listed in Table 1.3 [12].
Table 1.3 Electrical conductivity σ of biological tissues
| Tissue | σ (S/m) |
|---|---|
| Blood | 7.00E-1 |
| Bone | 8.07E-2 |
| Cartilage | 1.71E-1 |
| Fat | 4.04E-2 |
| Heart | 8.27E-2 |
| Kidney | 8.92E-2 |
| Muscle | 2.33E-1 |
| Nerve | 2.74E-2 |
| Skin (dry) | 2.00E-4 |
| Skin (wet) | 4.27E-4 |
The thermal injury will depend on the duration t of the contact and the temperature rise ΔT that the passing current will impose [19]. The thermal energy expressed in Eq. 1.2 is related to the temperature rise ΔT to which the volume of tissue is subjected. We can write the thermal balance equation (Eq. 1.3), which describes the exchange of heat between the heat delivered w and the heat accumulated in the volume of tissue, assuming σ independent of the temperature.
c is the volume-specific heat capacity, defined as the heat necessary to increase the temperature of a unit volume of a substance by 1˚C.
The temperature rise ΔT is given by Eq. 1.4
Equation 1.4 shows that the temperature rise ΔT depends on the square of the current density J and on the duration t of the current circulation.
The skin has the lowest conductivity among the biological tissues, and the current density is higher at the point of contacts on the body (referred to as entry and exit sites); therefore, for a given current, the highest temperature rise is achieved on the skin, which therefore suffers the greatest level of damage.
Thermal injury of the human skin occurs when the temperature rise persists for a sufficient length of time: for instance, to cause cutaneous injury, a temperature of the skin of 45°C requires a contact duration of 2 h; 51°C requires a contact duration of 2 min; and 60°C requires a contact duration of 3 s4 Current densities of a few mA/mm2 for a duration of about 0.5 to 1 s can cause burns, whereas a current density of a few tens of mA/mm2 for a few seconds, will cause third-degree burns with destruction of deeper tissues and possible necrosis.
Thermal shock can also be caused by the heat released by electric arcs, which are accompanied by the vaporization of metal to form a superheated toxic gas.
1.5 Heated Surfaces of Electrical Equipment and Contact Burn Injuries
Burns can also be triggered by unintentional contact with hot surfaces of electrical equipment, which may be readily accessible during normal operations (e.g., the surface of a PV module) [20, 21].
According to Stevens’ Law, the perception of temperature is also superlinear with the stimulus, as varies as the 1.6 power of the temperature (i.e., experimentally analyzed by using a heated metal on a person’s arm).
Most apparatus and appliances in industrial, commercial, and residential environments are thermally insulated unless the insulation would prevent their functions (e.g., the bottom surface of a flatiron). However, superficial temperatures of insulated equipment may still be high enough to cause burns from contact with readily accessible parts. The severity of such burns will depend on the thermal resistivity of the material of the touchable surface, and the pressure and duration of the contact.
An effective protection against burns can be established based on the acceptable contact period and on the level of acceptable injury.
According to the CENELEC Guide 295 for adults, a minimum contact period ranging between 0.5 s and 1 s should be used, based on the type of the equipment and where they are to be used (e.g., restrictive locations); however, extended reaction times may be considered based on the age of users that may possibly come into contact with the hot surface (Table 1.4).
Table 1.4 Standard contact durations
| Age Group | Exposure time (s) |
|---|---|
| Adults | 0.5–1 |
| age < 2 years | 15 |
| 2 years < age < 6 years | 4 |
| 6 years < age < 14 years | 2 |
| Elderly persons | 1–4 |
| Physical disabilities | According to nature of disability |
Once the maximum operating temperature of readily accessible surfaces is determined, by direct measurement or calculation, the potential injury level may be established through the graph of Figure 1.7, which shows the relationship between surface temperature and exposure time.
Figure 1.7 Temperature–Time Relationship for burns.
The bottom curve TB is the locus of the pairs temperature and exposure time representing the limit of the reversible epidermal injury; TB describes the acceptable injury level as a first degree burn, that