Muography. Группа авторов
Читать онлайн книгу.
upper Z Subscript 0 n Baseline comma beta Subscript n Baseline right-parenthesis Over q left-parenthesis upper X Subscript m Baseline comma upper Z Subscript 0 n Baseline comma beta Subscript n Baseline right-parenthesis EndFraction q Subscript h Baseline left-parenthesis upper X Subscript m Baseline comma z comma beta Subscript n Baseline right-parenthesis h left-parenthesis upper X 0 minus upper X Subscript m Baseline right-parenthesis EndLayout"/>
where m and n are the indexes of X and β, respectively.
The FBP technique was developed in the medical field for indoor use with X‐rays, and it is possible to increase the X‐ray beam intensity. However, the signal intensity is constant and limited in the case of muographic imaging, and the statistical error is an important consideration. Derivation of the equation for random error caused by the observed muon statistics is not straightforward; one simple solution is as follows. Assuming that the number of muon observations follows a Poisson distribution, we can assign random numbers to N i and reconstruct the image, and then iterate this procedure many times to evaluate the root‐mean‐square of the reconstructed density at every x, y, and z. This is represented by the following equation:
Figure 2.3 Schematic of the path length normalization approximation.
(2.19)
where j is the index of the trials in the simulation, J is the total number of simulation trials,
2.4 PERFORMANCE ESTIMATION WITH A FORWARD MODELING SIMULATION
This section describes an example of performance estimation using the two reconstruction methods.
The following assumptions and models were used in the simulation. The volcano selected as an example is Omuroyama, located in Ito, Shizuoka Prefecture, Japan. Omuroyama volcano is an inactive scoria cone that is part of the Eastern Izu Monogenetic Volcanic Group, and formed at ca. 4 ka. The basal diameter of the volcano is 800–1000 m, and its relative elevation is ~250 m. Multi‐directional muon tomographic study is ongoing at this volcano for the following reasons: (i) good accessibility for installation of muon detectors in all directions due to well‐maintained roads; (ii) the absence of “shadows” from any other objects in the background; and (iii) the volcano shape is axisymmetric, but non‐axisymmetric structures are expected in the volcano interior (Koyano et al., 1996; Saito et al., 2003).
The other parameters used in the simulation are as follows. The topographic data were published by the Geospatial Information Authority of Japan, and the grid size is 5 m for both the longitudinal and latitudinal directions. The minimum voxel unit that makes up the volcanic body is a cube with dimensions of 20 × 20 × 20 m3. We used two types of input density structures. One is a checkerboard structure, which consists of 100 × 100 × 100 m3 cubes with densities of 1.0 and 2.0 g/cm3, respectively (Fig. 2.5d). The other structure consists of two vertical cylinders inside the mountain, each cylinder has a density of 2.0 g/cm3 and a diameter of 100 m, and the rest of the mountain body has a density of 1.5 g/cm3 (see Fig. 2.9d). The detectors were placed on the surface in a near-circular array around the volcano (Fig. 2.4). The viewing range of each muon detector in the azimuth angle is ± 1.5 in tangent. The range in the elevation angle is 0.0–1.5 in tangent. The minimum size of the angular bins for the penetrating muon flux calculation is (0.01)2, then the number of muons in each bin was then merged into larger bins of (0.05)2 as shown in the Fig. 2.1. For simplicity, the thickness of the detector was assumed to be negligible compared with the length of the effective sensitivity plane, and all the muon detection efficiencies were assumed to be 100% with no angular dependence. The model for the muon fluxes was based on Honda et al. (2004), and we used the method of Groom et al. (2001) for the energy loss of high‐energy muons. The total summation product of the effective area × exposure time is 900 m2 d. For example, when the number of observation directions is 16, the product of the effective area × exposure time per direction is 900/16 = 56.25 m2 d.
Figure 2.4 Topography around Omuroyama volcano and the location of the muon detectors in the simulation. The coordinate origin is the summit of Mt. Omuro-yama (Latitude 34°54′ 11″, Longitude 139°5′ 40″). White dots imply the detector locations of the 16‐directional muography. In the case of 4‐directional muography, the detectors were placed at the northern, eastern, southern, and western points; in the case of 8‐directional muography, additional detectors were located to the northeast, southeast, southwest, and northwest. The small vent on the southern flank has an elevation of 450 m a.s.l.; the crater rim elevation is 535–580 m a.s.l.; the base of the crater is at 510 m a.s.l.
For simplicity, we assumed that the muon detectors have enough capability to reject low‐momentum particles (i.e., the effect of multiple Coulomb scattering is negligible). This assumption is required as the computational needs are too large to calculate the scattering effect. There have been several studies of the contamination of low‐energy particles due to the multiple Coulomb scattering effect around mountains (e.g., Ambrosino et al., 2015; Jourde et al., 2013; Nishiyama et al., 2014b, 2016).
2.5 RESULTS
Figs. 2.5–2.6 show the results of the reconstructions using the FBP and linear inversion methods with 4‐, 8‐, 16‐, and 32‐directional muographic images of a horizontal cross‐section at 470 m a.s.l. and a vertical cross‐section along a northing of 150 m, respectively. For the 32 points of the linear inversion, it was not easy to obtain a result due to the long computational time. Fig. 2.7 shows the reconstructed density and its random errors due to muon statistics along an easting coordinate at 470 m a.s.l. and a northing of 150 m. Fig. 2.8 shows the density profile along the elevation direction at an easting of −50 m and northing of 150 m. In the FBP plots in Figs. 2.7–2.8, there is a difference between the center value of the plot (reconstructed density without random numbers)