Body Sensor Networking, Design and Algorithms. Saeid Sanei
Читать онлайн книгу.
M is mass, k is the spring constant of the frame-substrate springs. By driving the resonating mass at a known frequency, its changing displacement D induces a voltage from which the angular speed can be derived reasonably linearly. However, as with MEMS devices, the problems of drift, noise, and other artefacts remain. An IMU can be a combination of both accelerometers and gyroscopes (and a magnetometer in a 9D version) that measures rate, angle, and direction of motion. IMUs can be attached to any part of the body and are effectively used in gait analysis. Recent IMUs have built-in magnetometers as well that sense gravity and can be used in fall detection.
3.2.3 Force Plates
Force plates measure vertical ground reaction forces (GRFs) applied by gait during walking. A force platform can be integrated under the moving belt of a treadmill or under the entire treadmill [31]. Force platforms are expensive and have some limitations as the plates are installed within a short space and need to remain stationary. These make their applications in free space difficult. Nevertheless, there are force or pressure sensors that can be accommodated inside or under shoes to monitor the walking steps of humans or help correct the posture of athletes.
3.2.4 Goniometer
A goniometer is used to track the angle changes and is used for angle measurement in gait analysis since it is flexible and can rotate proportionally to the joint angle being measured [32]. It is particularly useful for the analysis of ranges of motion. Using a goniometer, it is possible to determine the range of knee joint angular movement to monitor patients with knee injuries. An optical fibre-based goniometer has been introduced in [33].
3.2.5 Electromyography
Electromyography (EMG) is used to measure both physical (such as gait) and physiological activities (such as muscle diseases), as can be seen in Section 3.3. It represents the electrical potentials of neurons within the muscles and can be recorded using surface electrodes or by wires or needles inserted into the selected muscle of a lower extremity [34]. An understanding of muscle activity in gait can be obtained by processing the EMG signals. EMG provides feasibility of analysing relative contribution of the superficial muscles during movement. It records the activity of underlying motor units and plays an important role in clinical gait analysis for assessing walking performance of the people with gait impairments using muscle activity information, such as timing of the muscle activity and muscle strength.
3.2.6 Sensing Fabric
The goal in sensing fabric-based technology is the integration of sensors, communication components, and the processing elements into the fabric. The most common types are pressure sensors, including piezoelectric, piezoresistive, resistive, and capacitive sensors [35]. These sensors can be networked in a carpet to record the step pressure from both feet. In a more useful design, however, the pressure sensors and their associated electronics and wireless communication system, which does fit completely inside the shoe, is very demanding for the long-term monitoring and recordings of daily activities. Therefore, to make a valuable gait analysis platform, the sensing fabric technology has been directed towards the development of pressure-sensitive foot insoles with wireless communication capability [36].
3.3 Physiological Sensors
These sensors sense and capture the information emitted from the body inherently due to physiological or metabolic changes. These can be due to normal or abnormal human states. They can also be due to external effects such as viewing intriguing scenes, temperature change, and various physical activities.
3.3.1 Multichannel Measurement of the Nerves Electric Potentials
Electroencephalography (EEG), EMG, and electrocardiography (ECG) are probably the most common types of physiological measurement systems. They are widely available in the related clinical departments. In terms of operations, they measure, respectively, the electrical activities of nerves in the brain, muscles, and heart. Technically, low-noise differential amplifiers, with high amplification gains and large input impedance, are used to capture tiny variations in the voltage between each two electrodes or with respect to a common reference over the body. A typical three-stage differential amplifier is depicted in Section 3.5. Fundamental electronic components, such as operational amplifiers, resistors, capacitors, and diodes, are used to make this device. EEG and ECG (or even EMG) often involve a large number of channels. Nevertheless, due to their low bandwidth, the signals are often sampled in a low rate, which makes their real-time processing possible (Figure 3.4).
The EEG systems with their electrodes mounted over the cortex are called electrocorticography (ECoG) systems and those for measuring deep brain signals from deeper areas of the brain, are called intracranial EEG. In some applications, such as recording the neuron activities from the hippocampus, the measurement can be done by using multichannel electrodes inserted through human foramen ovale holes from both sides of the face. Figure 3.5a and b shows an ECoG and foramen ovale (FO) implant for deep brain source measurements.
Figure 3.4 A simple EEG differential amplifier used in EEG or EMG systems.
As another brain scanning modality, magnetoencephalography (MEG) is used to measure the magnetic fields produced by the electric currents in the brain. MEG and EEG look very similar. The advantage of MEG over EEG is its insensitivity against the changes in the tissue density, so it can be effectively used for more accurate brain source localisation. However, the system is complex, bulky, expensive, and not easily available for long-term patient monitoring, and requires a high maintenance cost.
ECG (also called EKG) is used to measure the electrical activity of the heart muscle nerves. The activity stems from pumping the blood through the right supraventricular down into the right ventricle and circling upward from the left ventricle to the left supraventricular and pumping into the arteries. Often 10–14 electrodes are used with reference to the arm, wrist or foot to capture the state of different heart sections.
The systems for measuring electrical activity of the body don't involve any time delay and therefore processing of EEG, MEG, EMG, and ECG doesn't suffer any fading, clutter, or time overlapping of the signals. On the other hand, the effective frequency range falls below 500 Hz, which requires low processing power and bandwidth.
There have been efforts to miniaturise these sensors with wireless capability. As an example, Figure 3.6 shows a new patch type ECG system which includes wireless connection to remote devices.
On the other hand, heart and lung sounds can be heard and recorded using electronic stethoscopes. They are sensitive microphones isolated from the surrounding environment when placed on the skin around the heart or back side of the body, so the ambient noise is greatly reduced. Most heart abnormalities as well as problems in the lung which cause wheezing or crackling can be easily heard and recorded through these systems. In some recent models, such as Modell 3200 by the Littman company (Figure 3.7), the stethoscope can also transmit sound signals via Bluetooth to the remote device for observation, archiving, and analysis.